Xact Woodturning Screw Chuck
- 1" x 8tpi & 3/4" x 16tpi
Woodscrew chucks are becoming increasingly popular due to their simplicity of use. They are commonly used when turning goblets, candlesticks, small bowls and pepper pots. You simply mark a cross on the end of your turning blank to create a centre point and then screw in the chuck. Once the screw is driven firmly home the end face of the turning blank seats itself against the face of the chuck to ensure concentricity.
Dovetail Jaws for 3" Woodturning Chucks - Xact, Record SC3, Viper 2
These dovetail jaws are deeper than the standard dovetails jaws supplied with Xact chucks and offer excellent work holding strength. The jaws are 20mm deep and have 10 machined serrations which are parallel to ensure maximum gripping power and strength. Externally the jaws are dovetailed and project 14mm from the base. The jaws expands from 38mm to 0mm and contract from 40mm to 28mm.
Face Plate for 4" Woodturning Chucks - Xact, Record SC4, Supa Nova, Viper 3
This face plate ring measures 75mm in diameter and features 8 screw holes. It is designed for securely attaching bowl blanks and due to the number of screw fittings, bowl blanks will remain rock solid even when initially roughing out. The rear of the face plate has a machine dovetail groove which matches the dovetail jaws supplied with the XT8000 Xact chuck or the XT9009 bowl jaws for the XT9000 chuck. We recommend bowl blanks up to 350mm diameter by 150mm width can be turned with this face plate.
Dovetail Jaws for 4" Woodturning Chucks - Xact, Record SC4, Supa Nova, Viper 3
These dovetail jaws are deeper than the standard dovetails jaws supplied with Xact chucks and offer excellent work holding strength. The jaws are 25mm deep and have 10 machined serrations which are parallel to ensure maximum gripping power and strength. Externally the jaws are dovetailed and project 16mm from the base. The jaws expand from 45mm to 70mm and contract from 60mm to 35mm.
King Japanese Sharpening Waterstone - Medium 1000 Grit - Extra Large
Used in the intermediate stages of restoring an edge or in the primary stage of sharpening a dulled edge, these man made Japanese waterstones will turn a dull edge into a sharp one very quickly. This extra large stone is excellent value for money for anyone who needs to do a lot of sharpening or who sharpens larger blades such as planer blades. Dimensions: 230 x 100 x 80mm.
Montana Magnetic Nut
Driver Set - 4 Piece
This 4 piece nut driver set is manufactured utilizing premium shock resistant S2 steel to reduce stress fractures and accessory failure. The drivers are heat treated to control hardness for superior strength and engineered and machined to prevent slipping and stripping. Each driver is fitted with an extra-strong neodymium magnet for fastener and nut retention and the drivers have a high resistance to abrasion for extended life and performance. The set comprises of 1/4", 5/16", 3/8" and 7/16" socket heads all mounted on a 1/4" hex drive system.
Machinery & Tooling
This is the best selling maintenance kit for woodworking machinery and tooling in North America. Includes router bit lubricant, saw blade and router bit resin and pitch remover, table top lubricant, bandsaw blade cutting lubricant. Proven formula's that improve the performance of woodworking tooling and machinery and improve the finish to woodworking projects. Used by over 1/2 million woodworkers worldwide.
Digital Read Out Kit - 600mm
This digital readout is designed so that you can adapt it to a number of woodworking machines, including router lifts, router tables, spindle moulders, table saws and planers. It features a remote display which is connected by a 1 metre cord which is easily disconnected for initial set-up and access. A large easy to view LCD display reads in millimetres and inches.
HSS Woodturning Skew Chisel
The skew chisel has to be the hardest turning tool to learn but once mastered, has to be the most versatile. Used correctly, a skew chisel will produce a fine finish to the surface of the wood that requires little sanding. The best indication is in the resultant waste as correct use will produce long curly shavings similar to those made with a plane. A skew chisel will produce grooves, coves, beads and V-cuts. Available in two sizes, these skew chisels have rectangular section HSS blades and American walnut handles.
HSS Woodturning Spindle Gouge
As the name suggests, spindle gouges are used for creating detail, such as coves and beads, on spindles. With a rounder tip and shallower flute than a bowl gouge, the spindle gouge is used to produce small radius concave and convex curves but can be used for creating larger radius curves and contours also. The smaller the gouge, the smaller the radii and details are that can be achieved. Available in two sizes, these skew chisels have rectangular section HSS blades and American walnut handles.
Montana Diamond Tile
Drill Set - 3 Piece
This diamond tile drill bit set contains 3/16", 1/4" and 1/2" bits that have exceptional cutting performance for drilling tile, glass and granite. They feature a core ejection slot for easy material plug removal and are 10x faster than standard glass and tile drill bits, with a 15x longer life than standard carbide tip spade drill bits. The patented sintered diamond edge combined with the tri-flat shank offer fast clean cutting performance whilst preventing bit spin out. On average you can drill 40 plus holes per drill bit.
Chrome Vanadium Combination Spanner Set - 25 Piece
This excellent set of metric combination spanners are drop forged and hardened and heat treated in chrome vanadium steel. They then have a high chrome polished mirror finish which is easy to grip and easy to handle. A twelve point profile on the inner of the ring spanner ensures optimum surface contact with the nut. This minimises wear and slippage on the nut. Each spanner is individually inspected and complies to DIN/OSI requirements for dimensional accuracy.
Famag SDS Carbide Tipped Masonry Drill Bits
Mounted on SDS shanks for use with SDS drills, these carbide tipped masonry bits will drill brick, stone and concrete. Made in Germany to strict tolerances, these bits produce true diameter holes for exceptionally accurate drilling unlike cheaper bits which often produce holes larger than stated. These drills cut very quickly and feature wide flutes to ensure good waste clearance which is especially important when drilling concrete.
Famag Bormax Forstner Drill Bits
These are the professionals choice in forstner bits. Perhaps looking more like a saw tooth bit than a convensional forstner bit, the Bormax bits are specially designed to give a perfect, clean cut quickly and accurately. The special waveform design gives the side of the bit a lower surface area reducing friction considerably which, in turn, reduces the amount of power used to drive the bit.
Shinwa Japanese Micrometer
- 0 to 25mm
An extremely useful workshop tool, the micrometer is often the measuring tool of choice for obtaining very fine, precise measurements. Offering a measuring range from 0 - 25mm in 0.01mm increments, this micrometer features highly durable etched scales that will not fade with use. The measuring heads have cabide inserts at the tips making them highly wear resistant. A locking lever holds the micrometer in position to make it easier to record measurements. With a measurement error of only +/- 0.01mm, this is a true precision measuring instrument.
Shinwa Japanese Precision
Protractor - 385mm
Offering exceptional precision in laying out, this stainless steel protractor features etched scales from 0-180 degrees reading both left and right. Set out in 0.5 degree graduations, the markings are laser etched for extra accuracy and durability. The pointer arm moves freely around the protractor and can be locked off at any angle using the large knurled nut. The other side of the arm has a handy 300mm scale etched along it to make measuring whilst marking out far easier. Made in Japan.
Shinwa Japanese Mitre Square
- 45 Degree
Made from stainless steel, this mitre square is precision ground for exceptional accuracy. The 45 degree square has a cut out window allowing for the marking of parallel lines as well as 45 degree angles. Mounted on a thick stainless steel base for added stability. Extremely accurate, the angles offer deviations of less than +/- 0.2mm per 100mm. Made in Japan.
Tradesmen's Marking Crayons
- Pack of 12
Made specifically for trade use these crayons will work on almost any surface including wood, wet wood, metal, concrete, plaster and glass. They are water proof and wear resistant and are manufactured from a non crumble marking compound.
Extra Long Auger Bit Set
- 6 Piece x 460mm
These Lewis pattern auger bits are used for deep wood boring and ensure rapid waste removal, leaving a clean, perfect diameter hole. These augers have a screw tip which allows them to bite quickly into the wood for precise, pin point drilling. A razor sharp spur starts the cut which is then followed by the cutting edge of the drill which removes the wood without tearing. This set of six comprises 10, 12, 14, 16, 18 and 20mm auger bits each with an overall length of 460mm.
Shinwa Japanese Precision Spring Balance - 0 to 30kg
A spring balance makes light work of weighing oddly shaped or bulky objects that will not fit on to conventional weighing scales. Accepting loads up to 30kg, this precision balance offers a good working weight range making it an excellent choice for the workshop. The measuring scale runs from 0 - 30kg in 0.5kg graduations and a screw at the top allows you to set the scale to zero to take into account the weight of any bag, sling or other method you use to fasten the object being weighed to the balance. Made in Japan.
Long Nose, Combination & Side Cutting Pliers - 170mm - Set of 3
All of the pliers in this set of three are manufactured from chrome vanadium. Chrome vanadium is renowned for being long lasting, hard wearing and corrosion resistant. Finely finished the working heads are machined for accuracy and all have precise wire cutting action.
Japanese Power Expansive Bits
Available in two sizes offering drilling diameters of 22mm - 50mm and 34mm - 80mm, these bits give you the selection of diameters without the expense of owning every individual size. Made from Japanese tool steel, these bits will drill hardwoods and softwoods with ease and the lip and spur shape of the cutting head give a straight, smooth sided, flat bottomed finish to your drill hole. The spur in the centre of the bits keeps the drill bit on course and the sharp spur scores and cuts the wood for a tear free finish.
Famag Extra Long Brad Point Drill Bits
With an impressive overall length of 250mm, these extra long brad point bits are perfect for deep hole drilling. Made in Germany from high speed steel, these bits are precision machined to give a perfect, true diameter hole. A pin point tip allows precise positioning of the bit and ensures the bit will stay on course during drilling. Razor sharp lips score the wood before cutting giving the resultant hole a clean tear free edge.
Famag Long Twist Drill Bits with Hex Drives
Offering a greater drilling depth than the short series drill bits, these long series bits allow you to change drill bits quickly with the minimum of downtime. Mounted on industry standard 1/4" hex shanks, these drills can be used with any quick change chuck or held directly in the drill chuck itself. Made in Germany from premium grade high speed steel, these professional quality drills are precision machined to give an accurate diameter when drilling, if you want a 10mm hole from the 10mm bit, that is what you will get.
Deep Pot Magnets - Set of 8
Deep pot magnets are very popular for workshop clamping and tool holding applications as they provide very powerful clamping forces, with the mild steel outer cup providing protection and mechanical strength to the pot magnet and inner magnet. This set comprises of 8 magnets: 4 x large 20mm x 20mm, 4 x medium 16mm x 16mm, each with their own keeper plate.
Aluminium Folding Rules
2 Metre - Pack of 3
These folding rules are an engineering classic and a must have for every discerning craftsman. Made from a special aluminium alloy with an anodised surface they feature a high contrast metric scale which ensures for a non-glare reading. The numbers and graduations are deeply etched on both faces and are extremely wear resistant. The anodising makes the rules weatherproof and highly resistant to tarnishing from grease and oils. Nickel plated steel springs ensure a precise smooth opening of the sections up to a full 2 metre length.
Made from 100% heavy duty cotton drill, this stylish baseball cap is the perfect way of keeping the sun off your head and out of your eyes. The rigid visor is shaped for improved shading. Fully adjustable, one size fits all with a hook and loop adjustment strap at the back.
Orthomat Anti-Fatigue Knee Saver - 530mm x 360mm
Designed with anti-fatigue properties which reduce the pressure on your knees and back to help blood circulation flow, this orthomat knee saver can reduce the effects caused by prolonged kneeling whilst at the same time, provide a durable working platform for jobs that demand labour intensive work from your lower body such as fitting skirting boards, tiling or perhaps carpet laying which would otherwise be uncomfortable. Measuring 530mm x 360mm, and 25mm thick, the knee saver is lightweight at only 450g and features a carry handle for easy transportation.
Water Pump Pliers - 10" - Set of 2
Water pump pliers are commonly used two at a time, one for holding the bolt the other for working the nut: hence our set of two. These 10" long pliers are fully forged and impulse hardened so that they are extremely strong and durable.
Famag Short Twist Drill Bits with Hex Drives
Made from premium grade high speed steel, these drill bits are ideal for pilot holes and short hole drilling in non ferrous metals. Mounted on a standard size 1/4" hex shank, these drills can be used in any quick change chuck or can be held directly in the drill chuck itself. Made in Germany, these bits are precision machined to give a true diameter hole making these the perfect choice when absolute accuracy is needed in your work.
Famag Lewis Pattern Auger Drill Bits
Measuring a generous 320mm, these individual Lewis pattern auger bits make light work of deep boring in wood. Suitable for cutting both hardwoods and softwoods, these augers are designed to leave a clean, tear free hole. The screw tip allows the auger to bite quickly into the wood and the cut is initiated by a sharp spur which is followed by the cutting edge of the drill to complete the cut.
Famag Brad Point Drill Bits with Cutting Lips
Made from premium quality high speed steel, these lip and spur bits are spceially designed for fast, clean cutting. The sharp lips score the wood prior to cutting giving a tear free edge to the hole and the central spur keeps the drill in position for more precise drilling. The large flutes have a parabolic profile giving these bits highly efficient chip clearance capabilities.
18 Gauge Staples - Pack of 1000
These 18 gauge staples are available in 6mm, 10mm and 12mm lengths and come supplied in a box of 1000. Compatible with the DK6785 Heavy Duty Hand Stapler & Nailer.
Knives & Limiters
This extensive range of spindle moulder knives and limiters is produced from premium quality German Tool Steel and can be used to produce profiles, joints and mouldings in all species of softwoods and hardwoods.