Premium Auger Drill Bit
Premium Auger Drill Bit
£7.99
inc. vat
Home > Drilling > Drill Bits > Auger Bits > Auger Bits > Premium Auger Drill Bit

Key Features

  • Lifetime Warranty
    If any bit fails due to a material or manufacturing defect it will be replaced free of charge
  • Made from a Special Grade of High Carbon Steel
    Extremely hard wearing and retains its hardness over prolonged use
  • Precise Cutting Geometry
    Ensures clean holes with minimal tearout on entry and exit of the hole
  • Threaded Centre Point
    Pulls the bit through the wood meaning little pressure is required
  • Deep Flutes
    Allows fast chip removal to prevent clogging when drilling deeper holes
  • Fully Ground
    Gives precise concentricity to ensure a highly accurate hole
  • Hexagonal Shank
    For a secure hold in the chuck to make sure the bit doesn't slip

Show more +

Product Details

These auger bits are the best that we have ever offered or tested and are perfect for quickly and accurately drilling deep holes through thicker stock. They can be used in a drill press or electric hand drill and are designed to be used on softwoods and hardwoods. The precise cutting geometry, a single cutting spur on the perimeter and a chisel like main cutter ensures accurate, clean holes while minimizing tearout on entry and exit of the hole. The cutting spur sits fractionally above the main cutter to ensure the bit enters the wood cleanly without tearing the wood fibres, the main cutter then follows to remove the material quickly to avoid the build-up of heat. The bits feature a threaded centre point which pulls the bit through the wood meaning minimal force is needed for the bit to work at full capacity. The deep flute allows fast chip removal to prevent clogging when drilling deeper holes.

The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. A hexagonal shaft ensures a secure hold that will not slip inside the chuck during use. Auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.

These bits are certified to ensure the dimensional accuracy of the hole and are available in 6mm to 26mm diameters in 2mm increments. The overall length of the bits is 230mm with a flute length of 170mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
These auger bits are the best that we have ever offered or tested and are perfect for quickly and accurately drilling deep holes through thicker stock. They can be used in a drill press or electric hand drill and are designed to be used on softwoods and hardwoods. The precise cutting geometry, a single cutting spur on the perimeter and a chisel like main cutter ensures accurate, clean holes while minimizing tearout on entry and exit of the hole. The cutting spur sits fractionally above the main cutter to ensure the bit enters the wood cleanly without tearing the wood fibres, the main cutter then follows to remove the material quickly to avoid the build-up of heat. The bits feature a threaded centre point which pulls the bit through the wood meaning minimal force is needed for the bit to work at full capacity. The deep flute allows fast chip removal to prevent clogging when drilling deeper holes.

The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. A hexagonal shaft ensures a secure hold that will not slip inside the chuck during use. Auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.

These bits are certified to ensure the dimensional accuracy of the hole and are available in 6mm to 26mm diameters in 2mm increments. The overall length of the bits is 230mm with a flute length of 170mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©

Show more +

Specifications

Brand Rutlands®
Material High Carbon Steel
Shank Type Hex
Shank Diameter 10mm
Overall Length 230mm

Show more +
5.000 1 5

Customer Reviews

Reviews (1)
Write Review....

Sam Dickenson

Ordered these yesterday for a lamp project I was making for my daughters birthday, they arrived today. They went straight to work drilling a hole all the way through an old 3" thick piece of hardened oak. Very easy to use and I didn't have to continually take out the bit to clear any chips.

Show more +
Show more +

Premium Auger Drill Bit

Rutlands®
Part No. M_R4037
£7.99 inc. vat

Quantity Discounts

Delivery

Order before 4pm Monday to Friday for Next Working Day Delivery

  • Royal Mail Tracked 24 (Below 2kg) - £4.99
  • Next Working Day UK - £6.99
  • 10am Next Working Day UK - £14.99
  • Saturday Next Day UK - £14.99
  • International - Choose Destination

Click & Collect

Order online and collect within 1 hour.

Collect from our Bakewell distribution centre between 10.00am and 5.00pm Monday to Friday

Find out more >

Returns

We're commited to selling high quality products, however we understand there can be times when items need to be exchanged or returned.

  • No quibble 30 day returns policy
  • Quick and simple returns process
Find out more >