Short Auger Drill Bits - Set of 6
£39.99
inc. vat
Key Features
- Lifetime Warranty
If any bit fails due to a material or manufacturing defect it will be replaced free of charge - Set of 6 Short Auger Bits
8, 10, 12, 16, 20, 26mm supplied in a wooden presentation box - Made from a Special Grade of High Carbon Steel
Extremely hard wearing and retains its hardness over prolonged use - Compact Size
Perfect for tight and confined spaces - Precise Cutting Geometry
Ensures clean holes with minimal tearout on entry and exit of the hole - Threaded Centre Point
Pulls the bit through the wood meaning little pressure is required - Deep Flutes
Allows fast chip removal to prevent clogging when drilling deeper holes - Fully Ground
Gives precise concentricity to ensure a highly accurate hole - 1/4" Hexagonal Shank
Compatible with all quick change shanks and gives a secure hold in the chuck to make sure the bit doesn't slip
Bundles
This Item: Short Auger Drill Bits - Set of 6
£39.99
Product Details
This set of 6 short auger bits are perfect for quickly and accurately drilling deep holes in thicker stock when you are working in small areas, their compact size means they can be used in tight and confined spaces. They can be used in either electric or manual hand drills and are designed to be used on softwoods and hardwoods. The precise cutting geometry, a single cutting spur on the perimeter and a chisel like main cutter ensures accurate, clean holes while minimizing tearout on entry and exit of the hole. The cutting spur sits fractionally above the main cutter to ensure the bit enters the wood cleanly without tearing the wood fibres, the main cutter then follows to remove the material quickly to avoid the build-up of heat. The bits feature a threaded centre point which pulls the bit through the wood meaning minimal force is needed for the bit to work at full capacity. The deep flute allows fast chip removal to prevent clogging when drilling deeper holes.
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. The quick change ¼" hex shank is compatible with all ¼" hex shank quick change systems, it will ensure a secure hold that will not slip inside the chuck during use. These short auger bits are normally used at low speeds between 400 and 1000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and the set contains 8, 10, 12, 16, 20 and 26mm bits. The overall length of the bits range from 110mm to 130mm with a flute length of 70mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. The quick change ¼" hex shank is compatible with all ¼" hex shank quick change systems, it will ensure a secure hold that will not slip inside the chuck during use. These short auger bits are normally used at low speeds between 400 and 1000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and the set contains 8, 10, 12, 16, 20 and 26mm bits. The overall length of the bits range from 110mm to 130mm with a flute length of 70mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
This set of 6 short auger bits are perfect for quickly and accurately drilling deep holes in thicker stock when you are working in small areas, their compact size means they can be used in tight and confined spaces. They can be used in either electric or manual hand drills and are designed to be used on softwoods and hardwoods. The precise cutting geometry, a single cutting spur on the perimeter and a chisel like main cutter ensures accurate, clean holes while minimizing tearout on entry and exit of the hole. The cutting spur sits fractionally above the main cutter to ensure the bit enters the wood cleanly without tearing the wood fibres, the main cutter then follows to remove the material quickly to avoid the build-up of heat. The bits feature a threaded centre point which pulls the bit through the wood meaning minimal force is needed for the bit to work at full capacity. The deep flute allows fast chip removal to prevent clogging when drilling deeper holes.
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. The quick change ¼" hex shank is compatible with all ¼" hex shank quick change systems, it will ensure a secure hold that will not slip inside the chuck during use. These short auger bits are normally used at low speeds between 400 and 1000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and the set contains 8, 10, 12, 16, 20 and 26mm bits. The overall length of the bits range from 110mm to 130mm with a flute length of 70mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. The quick change ¼" hex shank is compatible with all ¼" hex shank quick change systems, it will ensure a secure hold that will not slip inside the chuck during use. These short auger bits are normally used at low speeds between 400 and 1000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and the set contains 8, 10, 12, 16, 20 and 26mm bits. The overall length of the bits range from 110mm to 130mm with a flute length of 70mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
Show more +
Specifications
Brand
Rutlands®
Material
High Carbon Steel
Shank Type
Quick Change Hex
Shank Diameter
6.35mm
Overall Length
105mm - 130mm
Show more +
5.000
2
5
Customer Reviews
Reviews (2)
Write Review....
David Sage
Great set that cut really quickly. Nice clean holes. Very nice wooden case. Great service from Rutlands as usual.
Lee Meakin
Great little set supplied in a nice presentation box. Really easy use in both my drilling machine and hand power drill. The holes they leave are very clean and I have used these for some time now and not once have they burned any of my projects.
Show more +
£39.99
inc. vat
Quantity Discounts
Delivery
Order before 4pm Monday to Friday for Next Working Day Delivery
- Royal Mail Tracked 24 (Below 2kg) - £4.99
- Next Working Day UK - £6.99
- 10am Next Working Day UK - £15.99
- Saturday Next Day UK - £19.99
- International - Choose Destination
- Show Delivery Rates for
- Choose Destination
Click & Collect
Order online and collect within 1 hour.
Collect from our Bakewell distribution centre between 10.00am and 5.00pm Monday to Friday
Find out more >Returns
We're commited to selling high quality products, however we understand there can be times when items need to be exchanged or returned.
- No quibble 30 day returns policy
- Quick and simple returns process