Four Flute Auger Bit
£6.99
inc. vat
Key Features
- Lifetime Warranty
If any bit fails due to a material or manufacturing defect it will be replaced free of charge - Made from a Special Grade of High Carbon Steel
Extremely hard wearing and retains its hardness over prolonged use - Four Flute Design
For extremely fast cutting and immediate chip removal - Precise Cutting Geometry
Ensures clean holes with minimal tearout on entry and exit of the hole - Threaded Centre Point
Pulls the bit through the wood meaning little pressure is required - Deep Flutes
Allows fast chip removal to prevent clogging when drilling deeper holes - Fully Ground
Gives precise concentricity to ensure a highly accurate hole - 1/4" Hexagonal Shank
Compatible with all quick change shanks and gives a secure hold in the chuck to make sure the bit doesn't slip
Product Details
These four flute auger bits are ideal for quickly and accurately drilling deep holes in thicker stock. The four flute design is superior compared to single fluted auger bits when fast cutting and immediate chip removal is required. They can be used in either drill presses or electric hand drills and are designed to be used on softwoods, hardwoods and composite materials. The precise cutting geometry, the four cutting spurs, the four chisel like main cutters and the four flutes ensure accurate, clean holes while minimizing tearout on entry and exit of the hole. The cutting spurs sit fractionally above the main cutters to ensure the bit enters the wood cleanly without tearing the wood fibres, the main cutter then follows to remove the material quickly to avoid the build-up of heat. The bits feature a threaded centre point which pulls the bit through the wood meaning minimal force is needed for the bit to work at full capacity. The four deep flutes allow rapid chip removal to prevent clogging when drilling deeper holes.
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. The quick change ¼" hex shank is compatible with all ¼" hex shank quick change systems, it will ensure a secure hold that will not slip inside the chuck during use. These four flute auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and are available in 12mm to 20mm diameters in 2mm increments. The overall length of the bits is 165mm with a flute length of 75mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. The quick change ¼" hex shank is compatible with all ¼" hex shank quick change systems, it will ensure a secure hold that will not slip inside the chuck during use. These four flute auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and are available in 12mm to 20mm diameters in 2mm increments. The overall length of the bits is 165mm with a flute length of 75mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
These four flute auger bits are ideal for quickly and accurately drilling deep holes in thicker stock. The four flute design is superior compared to single fluted auger bits when fast cutting and immediate chip removal is required. They can be used in either drill presses or electric hand drills and are designed to be used on softwoods, hardwoods and composite materials. The precise cutting geometry, the four cutting spurs, the four chisel like main cutters and the four flutes ensure accurate, clean holes while minimizing tearout on entry and exit of the hole. The cutting spurs sit fractionally above the main cutters to ensure the bit enters the wood cleanly without tearing the wood fibres, the main cutter then follows to remove the material quickly to avoid the build-up of heat. The bits feature a threaded centre point which pulls the bit through the wood meaning minimal force is needed for the bit to work at full capacity. The four deep flutes allow rapid chip removal to prevent clogging when drilling deeper holes.
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. The quick change ¼" hex shank is compatible with all ¼" hex shank quick change systems, it will ensure a secure hold that will not slip inside the chuck during use. These four flute auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and are available in 12mm to 20mm diameters in 2mm increments. The overall length of the bits is 165mm with a flute length of 75mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. The quick change ¼" hex shank is compatible with all ¼" hex shank quick change systems, it will ensure a secure hold that will not slip inside the chuck during use. These four flute auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and are available in 12mm to 20mm diameters in 2mm increments. The overall length of the bits is 165mm with a flute length of 75mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
Show more +
Specifications
Brand
Rutlands®
Material
High Carbon Steel
Shank Type
Quick Change Hex
Shank Diameter
6.35mm
Overall Length
165mm
Show more +
5.000
1
5
Customer Reviews
Reviews (1)
Write Review....
Frank Walvin
Such quick drilling with these bits, in both hard and soft wood stock. The extra flutes really do make a difference to chip removal, I can drill straight through pieces without removing the drill.
Show more +
Four Flute Auger Bit - 12mm
Four Flute Auger Bit - 13mm
Four Flute Auger Bit - 14mm
Four Flute Auger Bit - 16mm
Four Flute Auger Bit - 18mm
Four Flute Auger Bit - 20mm
£6.99
inc. vat
Quantity Discounts
Delivery
Order before 4pm Monday to Friday for Next Working Day Delivery
- Royal Mail Tracked 24 (Below 2kg) - £4.99
- Next Working Day UK - £6.99
- 10am Next Working Day UK - £15.99
- Saturday Next Day UK - £19.99
- International - Choose Destination
- Show Delivery Rates for
- Choose Destination
Click & Collect
Order online and collect within 1 hour.
Collect from our Bakewell distribution centre between 10.00am and 5.00pm Monday to Friday
Find out more >Returns
We're commited to selling high quality products, however we understand there can be times when items need to be exchanged or returned.
- No quibble 30 day returns policy
- Quick and simple returns process