Premium Auger Drill Bits - Set of 6
£49.99
inc. vat
Key Features
- Lifetime Warranty
If any bit fails due to a material or manufacturing defect it will be replaced free of charge - Set of 6 Auger Bits
8, 10, 12, 16, 20, 26mm supplied in a wooden presentation box - Made from a Special Grade of High Carbon Steel
Extremely hard wearing and retains its hardness over prolonged use - Precise Cutting Geometry
Ensures clean holes with minimal tearout on entry and exit of the hole - Threaded Centre Point
Pulls the bit through the wood meaning little pressure is required - Deep Flutes
Allows fast chip removal to prevent clogging when drilling deeper holes - Fully Ground
Gives precise concentricity to ensure a highly accurate hole - Hexagonal Shank
For a secure hold in the chuck to make sure the bit doesn't slip
Bundles
This Item: Premium Auger Drill Bits - Set of 6
£49.99
Product Details
This set of 6 auger bits are the best that we have ever offered or tested and are perfect for quickly and accurately drilling deep holes through thicker stock. They can be used in a drill press or electric hand drill and are designed to be used on softwoods and hardwoods. The precise cutting geometry, a single cutting spur on the perimeter and a chisel like main cutter ensures accurate, clean holes while minimizing tearout on entry and exit of the hole. The cutting spur sits fractionally above the main cutter to ensure the bit enters the wood cleanly without tearing the wood fibres, the main cutter then follows to remove the material quickly to avoid the build-up of heat. The bits feature a threaded centre point which pulls the bit through the wood meaning minimal force is needed for the bit to work at full capacity. The deep flute allows fast chip removal to prevent clogging when drilling deeper holes.
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. A hexagonal shaft ensures a secure hold that will not slip inside the chuck during use. Auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and the set contains 8, 10, 12, 16, 20 and 26mm bits. The overall length of the bits is 230mm with a flute length of 170mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. A hexagonal shaft ensures a secure hold that will not slip inside the chuck during use. Auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and the set contains 8, 10, 12, 16, 20 and 26mm bits. The overall length of the bits is 230mm with a flute length of 170mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
This set of 6 auger bits are the best that we have ever offered or tested and are perfect for quickly and accurately drilling deep holes through thicker stock. They can be used in a drill press or electric hand drill and are designed to be used on softwoods and hardwoods. The precise cutting geometry, a single cutting spur on the perimeter and a chisel like main cutter ensures accurate, clean holes while minimizing tearout on entry and exit of the hole. The cutting spur sits fractionally above the main cutter to ensure the bit enters the wood cleanly without tearing the wood fibres, the main cutter then follows to remove the material quickly to avoid the build-up of heat. The bits feature a threaded centre point which pulls the bit through the wood meaning minimal force is needed for the bit to work at full capacity. The deep flute allows fast chip removal to prevent clogging when drilling deeper holes.
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. A hexagonal shaft ensures a secure hold that will not slip inside the chuck during use. Auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and the set contains 8, 10, 12, 16, 20 and 26mm bits. The overall length of the bits is 230mm with a flute length of 170mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
The auger bits are made from high carbon steel which has been hardened to ensure a long service life and give the bits impressive cutting properties when compared to traditional steel auger bits. The bits have been fully ground to give precise concentricity to ensure a highly accurate hole. A hexagonal shaft ensures a secure hold that will not slip inside the chuck during use. Auger bits are normally used at low speeds between 700 and 2000rpm to prevent the wood from scorching. The speed depends on size, with the larger diameter bits being used at lower speeds.
These bits are certified to ensure the dimensional accuracy of the hole and the set contains 8, 10, 12, 16, 20 and 26mm bits. The overall length of the bits is 230mm with a flute length of 170mm. These premium auger bits give an exceptional drilling performance and come with a lifetime warranty - if any bit fails due to a material or manufacturing defect it will be replaced free of charge. ©
Show more +
Specifications
Brand
Rutlands
Material
High Carbon Steel
Shank Type
Hex
Shank Diameter
10mm
Overall Length
230mm
Show more +
4.500
2
5
Customer Reviews
Reviews (2)
Write Review....
Rich
Comparable with the better brands available, the quality of these bits is really good. When drilling holes the bits never clog which I always find annoying. Ordered the set because there will always be a need for different sizes at some point. Would recommend.
Charles Morland
When using a pillar drill I prefer to use Forster bits for a nice clean finish. I though that at the price offered I'd chance it with a set of augers for when I'm working on larger timbers which are difficult if not impossible to get under a pillar drill.
To date I've only done some trial holes but have been very impressed. Freehand I've found that both corded and cordless drills have enough torque to deal with them. In fact I was expecting my 18 volt Makita cordless drill to struggle with the largest auger but it managed it with ease.
To date I've only done some trial holes but have been very impressed. Freehand I've found that both corded and cordless drills have enough torque to deal with them. In fact I was expecting my 18 volt Makita cordless drill to struggle with the largest auger but it managed it with ease.
Show more +
Premium Cryogenic M2 HSS Roughing Gouge - 1 1/2"
Precision Aluminium Straight Rule - 900mm
Precision Woodturning Screw Chuck
Precision Woodturning Screw Chuck - 1" x 8tpi
Precision Steel T Rule with Pencil and 12 Leads - 300mm
Precision 1/2" Router with Premium Guide Bush Set
Precision Aluminium Dado, Mortice and Groove Gauge
Digital Wheel Marking Gauge & Sliding Bevel - Set of 2
Premium Four Flute Auger Drill Bits - Set of 7
Precision 75 Woodturning Chuck Complete Kit - 1" x 8tpi
Precision 100 Woodturning Chuck Complete Kit
Digital Angle Rule, Digital Level Box & Digital Height & Depth Gauge - Set of 3
Premium Phenolic Multi Function Table Jig
Quick Release Clamps for Multifunction Tables - Pack of 2
Digital Level Box
Precision 75 Woodturning Chuck Complete Kit
Digital Sliding Bevel
Premium HSS Brad Point Drill Bits - Set of 8
T Track 4 Way Connector Kit - 19mm
Premium Phenolic Worktop Jig - Standard & Out of Square Joints
Premium Headless Pinner - 23g
Premium HSS Twist Drill Bits - Set of 25
Premium Phenolic Staircase Jig - Open & Closed Riser
Premium K10 Carbide Spindle Tool - Round
Premium Short Auger Drill Bits - Set of 6
Premium TCT Countersink Drill Bits with Low Fricton Depth Stops - Set of 3
Precision Steel Bend Rule with Pencil and 12 Leads - 180mm
Premium Router Circle Jig - 690mm
Premium Plug and Tenon Cutter
Premium Tenon Plug Cutters and Forstner Bits - Set of 4 - 15, 20, 25 & 30mm
Precision Aluminium Square - 400mm
Premium Guide Rail Clamps - Pack of 2
T Track Hold Down Clamps - 8.3mm and 19mm - Pack of 2
Digital Wheel Marking Gauge
T Track 4 Way Connector Kit - 8.3mm
Premium Short Auger Drill Bit
Premium Cryogenic M2 HSS Diamond Parting Tool - 1/8"
Premium HSS Brad Point Drill Bits - Set of 25
Digital Angle Rule & Digital Level Box - Set of 2
Premium Router Bit Holder - Pack of 2
Digital Tape Measure & Angle Finder - Set of 2
Premium Bench Top Router Table with R15 Router Lift and Motor
Premium Drill Bit Depth Stops - 2 Piece Set
Premium K10 Carbide Detail Tool - Diamond
Precision Aluminium Height and Drill Bit Depth Gauge
Premium Guide Rail - 1400mm
Ratchet Cable Clamp - Mixed Pack of 30
Precision Aluminium Straight Rule, Triangle Square and Square - Set of 3
Premium Mitre Gauge with Fence and Flip Stop
Premium K10 Carbide Hollowing Tool - Gentle Curve
Premium HSS Twist Drill Bit
Precision Aluminium Straight Rule - 600mm
Digital Angle Rule
Precision Woodturning 100mm Face Plate - 1" x 8tpi
Premium Pocket Hole Drill Bit - 9.5mm with Depth Stop
Premium TCT Countersink Drill Bit with Low Friction Depth Stop
T Track and Hardware Kit - Bumper Pack
T Track Left and Right Flip Stops - 19mm - Set of 2
Precision Aluminium T Square Rule - 260mm
Precision Aluminium Straight Rule - 300mm
Precision Aluminium 90° Square - 200mm
Precision Aluminium Triangle Square - 300mm
Digital Calipers
In Line Toggle Clamp - Auto Adjust Technology - 20mm
Premium Cryogenic M2 HSS Roughing Gouge - 1"
Premium Steel Pocket Hole Jig Kit
Premium Guide Rail Connector Bars - Pack of 3
Precision Steel T and Bend Rules - Set of 2
Premium Pocket Hole Plug Cutter - 9.5mm
Premium Cryogenic M2 HSS Spindle Gouge - 1/2"
Premium HSS Brad Point Drill Bits - Set of 16
Premium Forstner Sawtooth Drill Bits - Set of 6
Precision Aluminium Triangle Set Up Square - 140mm
Premium Cryogenic M2 HSS Woodturning Tools - Set of 6
Precision 100 Woodturning Chuck Complete Kit - 1" x 8tpi
Premium Cryogenic M2 HSS Bowl Gouge - 1/2"
Premium K10 Carbide Hollowing Tools - Set of 3
Premium R15 Router Lift & Motor
Aluminium Fence Clamps - Pack of 2
Premium Phenolic Lock Jig
Premium Forstner Sawtooth Drill Bit
Premium Aluminium Pocket Hole Jig Kit
Precision 100 Woodturning Chuck Kit - 1" x 8tpi
Premium Guide Rail Stop Blocks - Pack of 2
Digital Machine Set Up Tool
Digital Tape Measure
Precision Aluminium 45° and 90° Marking Square
Premium Cryogenic M2 HSS Skew Chisel - 3/4"
Premium Cryogenic M2 HSS Spindle Gouge - 1/4"
Precision Woodturning 13mm Drill Chuck
Premium Extra Long Auger Drill Bits - Set of 6
Precision 75 Woodturning Chuck Kit - 1" x 8tpi
Precision Aluminium Edge Marking Rule - 50mm
Premium K10 Carbide Woodturning Tools - Set of 3
Precision 100 Woodturning Chuck Kit
Premium Extra Long Auger Drill Bit
Premium K10 Carbide Hollowing Tool - Sharp Curve
Premium HSS Twist Drill Bits - Set of 19
Premium Phenolic Radius & Aperture Jig
Premium Guide Rail Saw Base
Premium Router Lift - R15
Premium Cryogenic M2 HSS Bead Forming Tool - 1/4"
Precision Aluminium Angle Gauge
Premium K10 Carbide Hollowing Tool - Straight
In Line Toggle Clamp with Angle Base Plate - Auto Adjust Technology - 20mm
Precision Aluminium Dual Wheel Marking Gauge
Premium Tenon Plug Cutters and Forstner Bits - Set of 4 - 8, 10, 12 & 15mm
Premium Forstner Sawtooth Drill Bits - Set of 15
Premium Cryogenic M2 HSS Round Nose Scraper - 3/4"
Premium Cryogenic M2 HSS Spindle Gouge - 3/8"
Premium HSS Lipped Brad Point Drill Bit
Premium Router Guide Bush Set - Metric
Premium Cryogenic M2 HSS Bowl Gouge - 3/8"
Precision Aluminium Square - 200mm
Premium K10 Carbide Roughing Tool - Square
Premium Box Joint Jig for Mitre Gauge
Precision Aluminium Tapered Edge T Square Rule - 200mm
Premium Mitre Trimmer
Precision Aluminium Adjustable T Rule - 200mm
Digital Angle Finder
Precision Stainless Steel Round Hole Gauge 3-15mm
Premium Guide Rail Saw Base Kit
Digital Height & Depth Gauge
Precision Aluminium Triangle Square - 150mm
Precision Woodturning 100mm Faceplate
Picture Frame Clamps - Pack of 4
Clamping Square and One Hand Bar Clamp Kit - 150mm - 4x Clamps & 10x Squares
Premium Cryogenic M2 HSS Square Nose Scraper - 3/4"
Precision 75 Woodturning Chuck Kit
Premium Table Saw Fence System - 1000mm
Premium Bi-Metal HSS Hole Saw Kit
Premium Headless Pinner Kit
Clamp Rack - Pack of 2
Premium Pocket Hole Screw Kit - 700 Piece
Aluminium Clamping Square with Clamps - 120mm x 120mm
Precision Aluminium T Square Rule - 160mm
Premium Four Flute Auger Drill Bit
Precision Woodturning 13mm Drill Chuck - No 2 MT
Pocket Hole Alignment Clamps - Pack of 4
Premium Auger Drill Bit
Premium Cryogenic M2 HSS Bowl Gouge - 1/4"
Premium Cryogenic M2 HSS Oval Skew Chisel - 3/4"
Premium Guide Rail Router Base Kit
Premium Guide Rail Router Base
Precision Thread Adaptor 1" x 8tpi Male to 3/4" x 16tpi Female
£49.99
inc. vat
Quantity Discounts
Delivery
Order before 4pm Monday to Friday for Next Working Day Delivery
- Royal Mail Tracked 24 (Below 2kg) - £4.99
- Next Working Day UK - £6.99
- 10am Next Working Day UK - £14.99
- Saturday Next Day UK - £14.99
- International - Choose Destination
- Show Delivery Rates for
- Choose Destination
Click & Collect
Order online and collect within 1 hour.
Collect from our Bakewell distribution centre between 10.00am and 5.00pm Monday to Friday
Find out more >Returns
We're commited to selling high quality products, however we understand there can be times when items need to be exchanged or returned.
- No quibble 30 day returns policy
- Quick and simple returns process