Router Bit - Raised Panel with Backcutter - Bevel - D=79.4mm H=30.2mm A=18° L=85.7mm S=1/2"
£69.99
inc. vat
Home > Router Bits > TCT Router Bits > TCT Router Bits > Raised Panel with Backcutter > Router Bit - Raised Panel with Backcutter - Bevel - D=79.4mm H=30.2mm A=18° L=85.7mm S=1/2"
Key Features
- Lifetime Warranty
If any bit fails due to a material or manufacturing defect it will be replaced free of charge - Undercutting Raised Panel Bits
Used to produce raised panels for doors, drawers and other panelled furniture - Save Time Producing Panels
The combined cutting profile produces a standard 6.35mm tongue in one cut, removing the need to adjust router bit height to fit rail & stile grooves - Diamond Ground Micro-Grain Tungsten Carbide Tips
Micro-grain structure means the blades offer long lasting hardness and superior edge retention - Perfectly Balanced Machined Steel Bodies
Reduce vibration for maximum control, producing a smoother cut and providing a longer bit life - Brazed By Induction
The tips are attached by induction creating an extremely strong joint between tip and body - Cutting Edge Shear Angle
Gives a smoother, slicing cut to eliminate tear-out and give a superior finish - Anti Kick Back Design
Allows you work safely in accordance with German DIN standards
Bundles
This Item: Router Bit - Raised Panel with Backcutter - Bevel - D=79.4mm H=30.2mm A=18° L=85.7mm S=1/2"
£69.99
Grip Blocks - Pack of 12
£39.99
This Item: Router Bit - Raised Panel with Backcutter - Bevel - D=79.4mm H=30.2mm A=18° L=85.7mm S=1/2"
£69.99
Product Details
TCT Router Bits
Each router bit features diamond ground, micro-grain tungsten carbide tipped blades. This tighter micro-grain structure means the blades offer long lasting hardness and superior edge retention. The body of each bit has been turned and then milled with uncompromising precision from a single piece of 4140 high tensile steel to give perfect balance for reduced vibration and therefore smoother cuts. 4140 steel has been chosen because of its toughness, high fatigue strength, and abrasion and impact resistance. The tungsten carbide tips are then brazed onto the bodies using induction to create an extremely strong joint that safely holds under the high stresses that occur when routing. The router bits are suitable for use on softwoods, hardwoods, veneers, laminates and composite materials.
Raised Panel with Backcutter Bits
Raised panel with backcutter bits are used to produce raised panels for doors, drawers and other panelled furniture. The profile combines that of a panel raising bit with a rabbeting bit and cuts both the front and back of the panel in the same cut. This means the resulting tongue will always be a standard 6.35mm size for slotting into the rail & stile grooves. This saves time by removing the need to adjust the router bit height so that the finished edge matches the rail and stile grooves. With a straight bevelled profile, this undercutting raised panel bit is well suited to creating modern style panel doors. For router table use only.
Superior Finish and Performance
The shearing angle of the cutting edges ensure they remain in constant contact with the workpiece to allow a smoother, slicing cut which eliminates tear-out and gives a mirror finish. The bits feature right hook angles which further enhances the cut due to the fast removal of chips. These bits feature an anti-kickback design which limits the feed rate of the material being cut to decrease the likelihood of a kickback, meaning each bit conforms to strict German DIN standards to ensure maximum operator safety. Each router bit features a lifetime warranty, if any bit fails due to a materials or manufacturing defect it will be replaced free of charge. ©
Each router bit features diamond ground, micro-grain tungsten carbide tipped blades. This tighter micro-grain structure means the blades offer long lasting hardness and superior edge retention. The body of each bit has been turned and then milled with uncompromising precision from a single piece of 4140 high tensile steel to give perfect balance for reduced vibration and therefore smoother cuts. 4140 steel has been chosen because of its toughness, high fatigue strength, and abrasion and impact resistance. The tungsten carbide tips are then brazed onto the bodies using induction to create an extremely strong joint that safely holds under the high stresses that occur when routing. The router bits are suitable for use on softwoods, hardwoods, veneers, laminates and composite materials.
Raised Panel with Backcutter Bits
Raised panel with backcutter bits are used to produce raised panels for doors, drawers and other panelled furniture. The profile combines that of a panel raising bit with a rabbeting bit and cuts both the front and back of the panel in the same cut. This means the resulting tongue will always be a standard 6.35mm size for slotting into the rail & stile grooves. This saves time by removing the need to adjust the router bit height so that the finished edge matches the rail and stile grooves. With a straight bevelled profile, this undercutting raised panel bit is well suited to creating modern style panel doors. For router table use only.
Superior Finish and Performance
The shearing angle of the cutting edges ensure they remain in constant contact with the workpiece to allow a smoother, slicing cut which eliminates tear-out and gives a mirror finish. The bits feature right hook angles which further enhances the cut due to the fast removal of chips. These bits feature an anti-kickback design which limits the feed rate of the material being cut to decrease the likelihood of a kickback, meaning each bit conforms to strict German DIN standards to ensure maximum operator safety. Each router bit features a lifetime warranty, if any bit fails due to a materials or manufacturing defect it will be replaced free of charge. ©
TCT Router Bits
Each router bit features diamond ground, micro-grain tungsten carbide tipped blades. This tighter micro-grain structure means the blades offer long lasting hardness and superior edge retention. The body of each bit has been turned and then milled with uncompromising precision from a single piece of 4140 high tensile steel to give perfect balance for reduced vibration and therefore smoother cuts. 4140 steel has been chosen because of its toughness, high fatigue strength, and abrasion and impact resistance. The tungsten carbide tips are then brazed onto the bodies using induction to create an extremely strong joint that safely holds under the high stresses that occur when routing. The router bits are suitable for use on softwoods, hardwoods, veneers, laminates and composite materials.
Raised Panel with Backcutter Bits
Raised panel with backcutter bits are used to produce raised panels for doors, drawers and other panelled furniture. The profile combines that of a panel raising bit with a rabbeting bit and cuts both the front and back of the panel in the same cut. This means the resulting tongue will always be a standard 6.35mm size for slotting into the rail & stile grooves. This saves time by removing the need to adjust the router bit height so that the finished edge matches the rail and stile grooves. With a straight bevelled profile, this undercutting raised panel bit is well suited to creating modern style panel doors. For router table use only.
Superior Finish and Performance
The shearing angle of the cutting edges ensure they remain in constant contact with the workpiece to allow a smoother, slicing cut which eliminates tear-out and gives a mirror finish. The bits feature right hook angles which further enhances the cut due to the fast removal of chips. These bits feature an anti-kickback design which limits the feed rate of the material being cut to decrease the likelihood of a kickback, meaning each bit conforms to strict German DIN standards to ensure maximum operator safety. Each router bit features a lifetime warranty, if any bit fails due to a materials or manufacturing defect it will be replaced free of charge. ©
Each router bit features diamond ground, micro-grain tungsten carbide tipped blades. This tighter micro-grain structure means the blades offer long lasting hardness and superior edge retention. The body of each bit has been turned and then milled with uncompromising precision from a single piece of 4140 high tensile steel to give perfect balance for reduced vibration and therefore smoother cuts. 4140 steel has been chosen because of its toughness, high fatigue strength, and abrasion and impact resistance. The tungsten carbide tips are then brazed onto the bodies using induction to create an extremely strong joint that safely holds under the high stresses that occur when routing. The router bits are suitable for use on softwoods, hardwoods, veneers, laminates and composite materials.
Raised Panel with Backcutter Bits
Raised panel with backcutter bits are used to produce raised panels for doors, drawers and other panelled furniture. The profile combines that of a panel raising bit with a rabbeting bit and cuts both the front and back of the panel in the same cut. This means the resulting tongue will always be a standard 6.35mm size for slotting into the rail & stile grooves. This saves time by removing the need to adjust the router bit height so that the finished edge matches the rail and stile grooves. With a straight bevelled profile, this undercutting raised panel bit is well suited to creating modern style panel doors. For router table use only.
Superior Finish and Performance
The shearing angle of the cutting edges ensure they remain in constant contact with the workpiece to allow a smoother, slicing cut which eliminates tear-out and gives a mirror finish. The bits feature right hook angles which further enhances the cut due to the fast removal of chips. These bits feature an anti-kickback design which limits the feed rate of the material being cut to decrease the likelihood of a kickback, meaning each bit conforms to strict German DIN standards to ensure maximum operator safety. Each router bit features a lifetime warranty, if any bit fails due to a materials or manufacturing defect it will be replaced free of charge. ©
Show more +
Specifications
Brand
Rutlands®
D
79.4mm
H
30.2mm
A
18°
P
6.35mm
L
85.7mm
n.max
12,000
S
1/2"
Show more +
5.000
1
5
Customer Reviews
Reviews (1)
Write Review....
Robert Jamieson
I purchased this raised panel cutter to make a load of window shutters...I'm really pleased with my purchase....very easy to set up and use...the back cutter gives a very nice detail!..and facilitates a range of panel thicknesses....I highly recommend Rutlands...very competitive price, excellent service and very speedy delivery.
Show more +
Router Bit - Raised Panel with Backcutter - Bevel - D=79.4mm H=30.2mm A=18° L=85.7mm S=1/2"
Rutlands®
Part No. R5629
£69.99
inc. vat
Quantity Discounts
Delivery
Order before 4pm Monday to Friday for Next Working Day Delivery
- Royal Mail Tracked 24 (Below 2kg) - £4.99
- Next Working Day UK - £6.99
- 10am Next Working Day UK - £15.99
- Saturday Next Day UK - £19.99
- International - Choose Destination
- Show Delivery Rates for
- Choose Destination
Click & Collect
Order online and collect within 1 hour.
Collect from our Bakewell distribution centre between 10.00am and 5.00pm Monday to Friday
Find out more >Returns
We're commited to selling high quality products, however we understand there can be times when items need to be exchanged or returned.
- No quibble 30 day returns policy
- Quick and simple returns process